Similar Products
King Springs
King Springs Jeep Wrangler JL Rear 50-100kg Coil Springs 40-50mm Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Jeep Wrangler JL 40-70kg Front Coil Spring 40-50mm Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Jeep Wrangler JL 50-100kg Rear Coil Spring 40-50mm Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs 200 Series 300-500kg Rear Coil Springs 40-50mm Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and present