King Springs
King Springs Isuzu MUX 100-300kg Rear Coil Spring 40-50mm Lift
$249.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Isuzu MUX 50-100kg Rear Coil Spring 40-50mm Lift
$249.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Jeep Wrangler JL 40-70kg Front Coil Spring 40-50mm Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Jeep Wrangler JL 50-100kg Rear Coil Spring 40-50mm Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Jeep Wrangler JL Front 40-70kg Coil Springs 40-50mm Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Jeep Wrangler JL Rear 50-100kg Coil Springs 40-50mm Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 100-250kg Front Coil Spring 40-50mm Lift
$249.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 100-250kg Rear Coils 40-50mm Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 150-250kg 3 Inch Rear Coil Springs Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 150-250kg Rear Coil Springs 4 Inch Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 250-350kg 3 Inch Rear Coil Springs Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 250-350kg Rear Coil Springs 4 Inch Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 300-500kg Rear Coils 40-50mm Lift
$359.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 50-100kg 3 Inch Front Coil Springs Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 50-100kg Front Coil Spring 40-50mm Lift
$249.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 50-100kg Front Coil Springs 4 Inch Lift
$279.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GQ GU 500-600kg Rear Coils 40-50mm Lift
$359.00
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 100-200kg Rear Coil 3 Inch Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 100-200kg Rear Coil 4 Inch Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 100-250kg Front Coil 40-50mm Lift
$124.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 100-250kg Rear Coil 40-50mm Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 250-350kg Rear Coil 3 Inch Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 250-350kg Rear Coil 4 Inch Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 300-500kg Rear Coil 40-50mm Lift
$179.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 50-100kg Front Coil 3 Inch Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 50-100kg Front Coil 4 Inch Lift
$139.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 50-100kg Front Coil 40-50mm Lift
$124.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
King Springs Nissan Patrol GU GQ LWB 500-600kg Rear Coil 40-50mm Lift
$179.50
King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing.
King Springs was established in 1956 on Queensland's Gold Coast.
Our complex comprises three adjoining factories spanning 8000 square metres.
Administration, manufacturing and warehousing all function from this one location employing over 70 people.
All King Springs are CAD designed
Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging.
Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections.
Gas heating is used for the furnaces for their clean and efficient heating
All coils are made with a computer controlled process for precise tolerances
Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness.
the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC
If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder
The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface
Dipped in phosphate for corrosion protection
Epoxy powder coated for a durable finish and presentation
King Springs
KTRR-70HD - 80 / 105 Series RAISED COIL Spring Rear (300-500KG)
$250.00
Kings Springs use high quality, high stress spring steel.
This newer generation steel allows King Springs to further improve many of their existing designs by reducing the amount of steel required in a spring, making it substantially lighter (by approximately 30%) and reducing the solid height therefore increasing travel. Being of particular benefit at all top levels of Motorsport, this new high stress material was introduced to the leading v8 super car teams (inc DJR/TP, FTR & NISSAN) in early 2007 giving a hugely successful endorsement of its characteristics & proven durability.
Although considerably expensive, King Springs have introduced this new high stress steel to their passenger car and 4wd designs which benefit the most at no extra cost to the consumer.
All King Springs heavy duty replacment springs are designed to be uprated. The degree of uprating varies between vehicles, but can generally be stated at 20-40%.
Carbon Offroad
LAND CRUISER 200 SERIES REAR SPRINGS SET
$100.00
Good condition 200 series land cruiser rear springs, very minimal surface damage, good condition
Diesel Power Modules Tuning Chips
Land Rover Defender 2.2 4x4 Diesel Power Module Tuning Chip
$749.95
Diesel Power Modules has been manufacturing and developing performance chip modules in Germany for over 20 years. With this experience, we have developed a range of performance modules specifically for the Australian 4wd vehicle.
30 Day no questions asked money back guarantee. Buy a Diesel Power Module, try it out for a month, if you do not like it for any reason, return to us for a full refund.
Why Diesel Power �
The modern diesel engine lacks low-end power. To Improve this, Diesel Power has increased low-end torque through active software power programming. This gives you more usable power and torque especially if you�re towing or 4wding.
How it works �
Diesel Power intercepts signals from the factory ECU and sensors and modulates them using a 64mhz V2 processor. This increases power and torque at set RPM points
Benefits �
Simply plug in and go � no dyno tuning required
Does not exceed factory ECU settings
User adjustable for power and economy
Towing? � Larger Tyres? � Heavy Accessories? � YOU NEED DIESEL POWER!
FEATURES
Super fast high quality 64mhz V2 processor � For a smoother power delivery
Active Software Programming � Automatically adjusts to suit engine loads
3 Year Warranty � Australia wide � no fuss exchange warranty
Simple to Install � 15-30 mins for plug-in modules
O.E Style Waterproof Plugs � Model Specific Wiring Looms
High-Quality Manufacturing � Made and Developed in Germany
User Adjustable � Economy & Power
Hi-Impact Case � Robust ABS plastic, dustproof / water resistant
Solid State Electronics � Military Grade resin coated heavy duty PCBS
E1 & TUV Certified � High-Level European consumer certifications
Compliant Emissions � Your vehicle will maintain emissions compliance with module fitted.